Updated November 2026
A Spypoint Flex-Plus cellular trail camera sends photos to your phone without a return trip to the stand, but only if it is activated, aimed and placed correctly. This guide walks you through activation, core settings, and placement so the camera reliably captures deer and not blown-out branches. Work through the steps in order before your first scouting trip. You may also like Spypoint LM2 Cellular Trail Camera: Setup, Plan and Placement Steps.
Step 1: Activate Cellular Service First
Most cellular trail cameras will not send anything until the data plan is active, so start there. Create your account in the Spypoint app, add the camera using the serial number on the back, and select a plan that matches how many photos you expect to send. If you are unsure how much data you will use, read the Trail Camera Data Plan: How to Choose and Save on Cellular Service article before you commit.
Shopping for one? See our guide: Spypoint Flex G36 Cellular Trail Camera Review: Is It Worth It?.
Confirm the camera shows a signal before you walk into the woods. Check the signal indicator in the app and test with a few photos at home. Signal strength varies by carrier coverage, so check the carrier’s coverage map for your property and call ahead if you are unsure about service in your area.
Step 2: Configure the Core Settings
Good settings reduce wasted photos and keep your data usage under control. Set the following in the app or the camera menu:
- Photos per trigger: Use 1 to 3 photos for general monitoring. A higher count helps you track movement but uses more data.
- Sensitivity: Start at a medium setting. Raise it only if you are missing deer at close range.
- Delay between triggers: Shorter delays capture more activity but send more images. Longer delays protect your data plan.
- Time-lapse or scheduled photos: Use these sparingly, since they multiply transmissions.
Manufacturers recommend checking the firmware version in the app before field use, so install any update that is offered.
Step 3: Place the Camera for Clean Detections
Mounting height and angle matter more than most settings. Mount the camera roughly 3 to 4 feet off the ground for deer, and angle it slightly downward so the trigger zone covers the trail at 20 to 30 feet. Face the camera away from the sun, since a low morning or evening sun can wash out images and trigger false photos from heat shifts.
Clear grass, low limbs and brush inside the detection zone. Swaying vegetation is the most common cause of empty photos that still use your data.
Quick Field Checklist
- Data plan active and signal confirmed before leaving home
- Photos per trigger and delay set to match your plan
- Camera mounted 3 to 4 feet high, angled down
- Sun behind the camera or off-axis
- Vegetation cleared from the detection zone
- Test photo sent and received on your phone
Step 4: Check Performance and Adjust
After the first few days, review the photos in the app. If most images show empty trails, raise the sensitivity threshold slightly or clear more brush. If you see deer only partially in frame, lower the mounting height or tilt the camera down. Make one change at a time so you know what worked.
Common Mistakes to Avoid
- Leaving the default delay and photo count in place, which drains data quickly.
- Mounting too high, so animals pass below the trigger zone.
- Pointing the lens at open sky or a sunrise, which causes overexposed images.
- Skipping a signal test before the camera goes into the woods.
- Ignoring nearby camera setups that can overlap and trigger each other. For a broader look at setup approaches, see Spypoint Flex Cellular Trail Camera: Setup and Settings Guide.
Recommended Gear
- Spypoint Flex-Plus is the camera itself, and it is the right starting point for a cellular setup in most deer properties. View on Amazon
- Trail camera tree strap or mounting bracket keeps the camera steady and at the correct height on uneven trees. View on Amazon
- Solar panel or spare battery pack extends field time between service trips, especially in cold weather. View on Amazon
FAQ
Why is my Spypoint Flex-Plus not sending photos?
The most common cause is an inactive or suspended data plan, or weak carrier signal at the mounting location. Check the app for plan status and signal strength, then move the camera to a spot with better coverage if needed.
How many photos should I set per trigger?
One to three photos works well for most deer monitoring and balances useful detail against data usage. Increase the count only when you need to track movement across the frame.
What mounting height is best for deer?
Roughly 3 to 4 feet off the ground, angled slightly downward, covers deer at typical trail distances. Adjust based on what you see in your first set of photos.
Conclusion
Activate your data plan, set conservative photo and delay values, and mount the camera at a height and angle that covers the trail. Review the first few days of photos and make one adjustment at a time. With those steps done, your Spypoint Flex-Plus will deliver useful images without wasting data.

