Updated November 2026
A tactacam reveal x 3.0 cellular trail camera 2-pack lets you monitor two spots at once and get photos sent to your phone without walking the property. This guide walks through what you need before you start, how to set up both cameras, how to place them so they capture useful images, and how to keep them reporting. Follow these steps in order and you should have both units sending photos within one session.
What You Need Before You Start
Gather the supplies first so you are not stopping mid-setup. Confirm your cellular plan is active before you deploy anything in the field.
Shopping for one? See our guide: Tactacam Reveal Ultra Cellular Trail Camera Review: Key Features Explained.
- Both camera units, each with fresh batteries rated for cold weather
- A working SD card for each camera, formatted in the camera’s own menu
- A smartphone with the Tactacam app installed and logged in
- An active cellular data plan matched to each camera (see Tactacam Trail Camera Plans: How to Choose and Activate One (2026))
- Mounting straps, a small level, and a phone with a signal-strength app
Step 1: Activate and Name Each Camera
Activate each unit separately in the app before mounting. Give each camera a distinct name tied to its location, such as “North Scrape” or “Creek Crossing,” so the photo alerts are easy to sort. Naming is a small step, but it saves real time when two cameras are sending images during the season.
If a camera will not register, check the account details and signal before assuming a hardware fault. Many connection problems trace back to the plan or the coverage area, which is covered in US Cellular Trail Camera: Why It Won't Connect and How to Fix It.
Step 2: Test Signal Before Mounting
Walk to each planned spot and check cellular signal with your phone. Mount each camera only where you have at least two or three bars on your carrier. A camera that is not getting signal at the tree will drain its battery searching for a connection and send little or nothing.
If signal is weak, move the camera slightly toward higher ground or a more open line of sight to the tower. Shifting a few dozen yards can change the result completely.
Step 3: Set Height, Angle and Field of View
Mount both cameras at a consistent height, roughly waist to chest level for most deer work, and angle them slightly downward. Keep the sun out of the lens as much as possible, since a sun-facing camera washes out frames during morning and evening.
- Aim at a pinch point, trail, or food source about 15 to 25 yards away.
- Clear brush and low branches inside the detection zone so they do not trigger false captures.
- Use a level on the mount so the image is not tilted.
- Take a test photo and adjust until the target area fills a good part of the frame.
When both cameras cover different sides of the same food plot or travel corridor, you can compare movement patterns across the two sites. Plan your placement on a map before you walk in.
Step 4: Confirm Both Cameras Are Reporting
Trigger each camera by walking in front of it and confirm the photo appears in the app. Wait long enough for the transmission to finish, since cellular delivery is not instant. Check both units again the next day to make sure neither dropped off the network overnight.
Keep an eye on battery level and plan data usage so a camera does not go silent mid-season. Manufacturers generally recommend checking connectivity periodically rather than assuming it stays stable.
Common Mistakes
- Mounting before testing signal, which leaves one camera silent all season.
- Aiming into the morning or evening sun and getting washed-out frames.
- Leaving tall grass or branches in the detection zone and triggering constant false photos.
- Using one data plan assumption for both cameras without confirming each one is active.
- Skipping the test walk, so the camera fires too late or misses the animal entirely.
Recommended Gear
- Cold-weather lithium batteries help maintain power in low temperatures, which matters for cellular units that transmit often. View on Amazon
- Adjustable trail camera straps let you lock the angle and height so the cameras stay put. View on Amazon
- High-capacity SD cards give you room to store photos locally as a backup. View on Amazon
FAQ
Can both cameras share one data plan?
Each camera generally needs its own activated line with the carrier that supports your model. Check the plan details for your specific camera before assuming they can be combined.
How far should the two cameras be from each other?
Spacing depends on the terrain and what you want to compare. Placing them to cover different travel routes or feeding areas gives you more useful information than placing them side by side.
What should I do if a photo never arrives?
Check signal at the camera location, confirm the plan is active, and verify the battery level. If problems continue, contact the manufacturer’s support for model-specific help.
Conclusion
Activate and name both cameras, test signal before mounting, and aim each unit at a consistent, well-lit target. Confirm photos are arriving from both sites before you leave the property. A short check at the start of the season prevents most of the problems hunters run into later.

